Creation of an automotive component
In previous articles we talked about various aspects of mechanical design, such as, for example, implementing the development of a new automotive component, from concept to design. In this third appointment we will instead see some guidelines on how to build mechanical parts. Our target is to have an innovative product, with high quality and performance, without neglecting crucial aspects such as cost control and time planning.
In each race the timing is perfectly defined: it is not possible to change a deadline. On the scheduled day, at the scheduled time, you must be on the starting grid with the engine running and the car ready. Therefore, time management and meeting deadlines are a determining factor in achieving victory. If, for example, we have a good intuition, from which we expect an improvement in performance to use it on the track, it is necessary to follow all the phases of its implementation.
The phases are: the technical definition through drawings and specifications, the choice of the supplier who will build the pieces, the issuing of purchase orders and commercial negotiations. Then the last phases are: the definition of delivery times, the transport and packaging of the parts, the verification of the correct execution of the components, the assembly, the preliminary tests, the start-up, and, finally, the testing on the track.
How to avoid manufacturing errors
To be able to build the pieces we must have the construction drawings, as well as the technical specifications of the various components. Drawings and specifications are, of course, the main language to use with workshops and suppliers. Verbal explanations, while remaining useful for clarification, are dangerous because they are interpretable and because they can be easily forgotten. Furthermore, the choice of suppliers is a fundamental aspect for the success of a new project. Especially when the components are not standard, and therefore must be tailor made, and the quantities are very low.
Sometimes, we have to create only a few pieces. In similar situations, manufacturing errors are just around the corner, and in the world of racing and performance there is rarely the opportunity and time for a second chance on the track. We must therefore be sure that the supplier has the know-how, the necessary technology, and finally has experience in the manufacture of similar components. The supplier should then be involved once the design is unfinished. In this way you can satisfy your needs as much as possible using your experience on technological aspects.

It is extremely important to maintain an active role in every phase of the design and manufacturing of an automotive component.
Quality Check
During the period in which the supplier carries out the work, which can last a few weeks, it is important not to maintain a passive role of simply waiting for the delivery of the pieces. We have to verify that no problems arise by calling, making visits to the workshop to see the manufacturing process. We have to follow the construction actively.
Then, finally, our components will arrive. At this point the instinct would be to assemble everything in a hurry, go to the track and see the results. Instead, it is important to be rational: the risk at this point could be to nullify the work done. In fact, after delivery, each piece must be checked before mounting on the vehicle. And unfortunately it is not so obvious that the components are consistent with the design. This is why a quality control must be carried out.
Partial assembly for each automotive component
This static verification of dimensions, tolerances, weight, materials – and any other necessary aspect – identifies in advance any defects that could cause failures on the track. Failures are effectively dangerous for the integrity of the driver and the car, even before the result.
Partial assemblies are then carried out to verify that each automotive component correctly fits. Until a few decades ago, before the advent of three-dimensional design and numerically controlled machine tools, this was the moment of “settlement”. That is, the phase in which the pieces that presented design or manufacturing inconsistencies were modified – or recovered. Today, design and production techniques have evolved greatly, and errors are therefore very rare. Despite this, some fine-tuning was still carried out, as it remains a fundamental phase for the development of a new project. Subsequently, functional tests are carried out on the various parts, verifying functionality and performance.
Other considerations may concern the structural characteristics of the frame such as stiffness, resistance to stress, resistance over time, crash resistance (very important for the safety of the driver and passengers) and the dynamics of the structure (frequencies, damping, and so on ). It is therefore necessary to manage the overall dimensions as best as possible, as well as setting the attacks of the various groups, and making the most appropriate choices regarding reliability, repairability and maintenance.
Circular interaction
Once everything has been verified and tested, we can proceed with the definitive assembly of each individual automotive component. Every project must be well constructed and assembled to become successful. Assembly must therefore be carried out with care. The mechanics must then be perfectly informed in detail about the methods and particularities of assembly: this can be done through sketches, drawings and procedures. In new projects, in fact, nothing must be taken for granted. Everything is sized to the millimetre as even small inaccuracies in assembly can cause problems.

Creation of a 6-speed gearbox
A gearbox is essentially a metal box containing gears. It is positioned between the engine and the differential, which transmits motion to the driving wheels. But what is the gearbox for, and why do all cars have one? Let’s take a paradoxical example. The wheels of a Punto, if they were connected directly to the crankshaft, would rotate at around 5000 rpm. Theoretically, the car would travel at around 520 km/h. Similarly, a Ferrari Formula 1, at 18,000 rpm would run at around 2200 km/h – more than double the speed of sound, i.e. like a military fighter.
This is not possible, or rather it would be if the car did not have to overcome the rolling friction of the tires. And, above all, air resistance. These speeds are not achievable because the engine thrust (driving torque) is not sufficient to compensate for these resisting forces. Furthermore, in this configuration the car would not even be able to start: it would be like trying to start from a standstill with fifth gear engaged.
The gearbox in a car
By placing gears between the engine and wheels the speed is reduced, but at the same time the driving torque increases. This is achieved by having a larger gear wheel driven by a smaller one, thus creating a speed reducer. The gearbox is nothing more than a reducer in which the ratios are variable. The driver chooses them by operating the lever inside the passenger compartment.
The reduction ratio must be high in the 1st and 2nd gear to have a lot of torque at the wheels. Although it is true that air resistance is low at low speed, excess torque is needed to accelerate the vehicle starting from a standstill. By moving to higher gears the reduction ratio decreases to stimulate the speed of the car.
The gearbox of a racing car
The gearbox of a racing car is much more than a simple automotive component: it must be light, with small size, and must offer a decidedly rapid gear change. Furthermore, a correct choice of gear ratios is particularly important, both in relation to the engine torque curve, the aerodynamic efficiency and, finally, the weight of the vehicle. Generally, multiple sets of gears are made with a different reduction ratio (longer or shorter). And before the race, depending on the circuit and other parameters, you can choose the ones you want by replacing the gears on the gearbox shafts.
With these aims we have created an evolution of a 6-speed gearbox. The main aim was to reduce weight, lightening the gears thanks to the use of special materials and treatments and also modifying the type of meshing between the cogwheels. Now, here’s a new example. Let’s say that five new changes need to be made in two weeks. And we only have the drawings in our hands.

Example of a complete program
Our program is: we purchase the commercial parts (bearings, bolts, oil, etc.), we build the components (gears, shafts, etc.), we have the heat and surface treatments carried out, we check the components, we assemble the pieces and finally we start the testing.
Remaining in our example, even if the drawings were not ready yet, we had already spoken with the gear supplier about ten days ago. The target was to book machines and operators. We also made sure that he already had the material to work with (quality steel, difficult to find) and the tools. In this way we have eliminated any downtime.
Meeting suppliers
The gears must be machined, heat treated in the oven, taken back to the shop with the grinding machine and undergo another final heat treatment. This means that they must be transported between the workshop and the treatment provider at least four times. Any courier, no matter how fast, would take at least four days. We therefore decide to transport the pieces personally. In this way, we are certain that they will not remain forgotten in some corner, awaiting shipment. Furthermore, we maintain direct and continuous contact with the partners and suppliers, checking the work, requesting and reminding everyone of their duties and deadlines.
During these meetings with suppliers we make them understand the importance of our project for the success of the race, involving them in the aim of performing well in the championship. A victory is a great satisfaction for those who race themselves and for the team that follows them, but it also is a great satisfaction for all the people who collaborated in different roles to create the car.
Possible unexpected events
Here’s an unexpected event. We are having difficulty sourcing some types of bearings. Since these are uncommon bearings, they have a supply time of fifteen days, and the program risks being canceled completely.
After a technical meeting we decide on an emergency solution. That is, we order easily available bearings, different but in the same size, with a shorter expected life. They will definitely let us finish the first race. For the next ones, when better quality bearings is available, we will replace them.
Compromise can be a solution
We make sure that everything in the workshop is ready when the automotive components to be assembled are available. We organize a meeting with the mechanics to remind us once again how important attention to every detail is. We inform them about the features of the new gearbox, provide assembly instructions and illustrate the drawings. In this way we will be able to save some more time. As soon as we receive te parts the mechanics will be able to start working immediately.
The final assembly
Four days before the race we have all the automotive components in the workshop. It is a very exciting moment, because we finally see for real what we had only imagined or, at most, seen on the computer and on paper. At the same time we feel the slight sense of uncertainty that accompanies every new project, the potential risk that something won’t work properly. At this point, the best way to be competitive is to believe in our work, and carry out checks on the pieces and final assembly with the utmost care. Now everything is ready and mounted on the car. The race is waiting for us…
